CORTIG 200 AC/DC PULSE TIG - Digital Inverter Welder COR 200ACDC

Equipment Manuals https://www.coreonewelding.com/equipment-manual.html

TIG Welder with Foot Pedal and more...

The CORETIG 200 AC/DC is the new standard for Dual voltage welders making it the affordable ideal choice for both the experienced professional TIG welder and the Weekend Warrior alike. With a 3 year warranty this machine has unbelievable performance and features. TIG consumables Sold Separately.

Info Sheets

CORETIG 200 AC/DC Information Manual and Sell Sheet

Learn more

TIG Welding Equipment by Coreone

Coreone TIG Welding Equipment

Comes complete with 200 AMP AC/DC Tig Machine, 13 foot WP/SR17 TIG Torch, 13 foot Ground Cable with Clamp, Argon Flow-meter with 6ft Gas Hose with fittings, 115v / 230v input cord adapter. TIG Consumables Sold Separately

Coreone TIG Welder

The CoreTig Digital Pulse 200 amp AC/DC inverter controlled squarewave machine sets the standard for a "premium" performance tig machine at an agressive price. With a 3 year warranty this machine has unbelievable performance and features. Operates on 115v and 230volt.

The Competitive Edge

This Welding Machine is built to our rigorous specifications and manufactured in compliance to CAN/CSA 60974.1

The full TIG functionality, offers simple step by step digital control of functions and parameters providing complete professional control. HF arc ignition provides Pre Gas with instant arc ignition leaving no tungsten inclusion or contamination of the tungsten electrode. Digital set-up of Pre-Gas Flow Time, Start Current, Up Slope and Down Slope Time, Finish Current Level and Post Gas Flow Time with the choice of 2T or 4T trigger function allows control of the welding process at a professional level from start to finish. Digital Pulse Control gives full parameter setting of Peak & Base Current, Pulse Frequency & Pulse Width providing control of heat input, penetration & distortion. AC Square Wave Balance gives control of the electron flow at the tungsten, the AC TIG arc can be adjusted from maximum oxide-layer cleaning on aluminum through to a deeper penetrating weld. Remote Control Interface provides remote amperage control at the footpedal control. The Selectable Tungsten feature allows the user to initiate softer arc starts when using small tungsten with thin metals avoiding burn through on their work. When using a larger tungsten it requires a larger initial current and by selecting a larger tungsten size it avoids arc stutter or lack of arc initiation. DC ARC welding delivers a smooth and stable arc for easy welding of electrodes producing high quality welds including cast Iron, stain-less and low hydrogen. Arc Ignition and Arc Force control allows you to set the ideal arc condition no matter what electrode you choose. Optimized auto protection of the power input provides auto shut down of the machine when large scale fluctuations occur. Unique air channel design increases the heat dissipation of the power device, control circuits, minimizes dust absorption, thereby greatly improving longevity and reliability.

Manuals for Coreone Equipment

Complete Manual List: Click Here

Product Details

The Latest 43KHz State Of The Art Inverter Technology
AC/DC HF TIG/ARC Function
Arc Ignition HF Oscillation
AC Square Wave 20 - 250Hz
AC Balance Control Adjustable
Pulse Frequency 1 - 200Hz
Pulse Width 50%
Base Current 5 - 200A
Up Slope 0 -10 sec
Down Slope 0 -15 sec
Pre Gas 0 - 5 sec
Post Gas 0.5 -20 sec
Trigger Function 2/4T-Spot
Arc Ignition Current Automatic
Arc Ignition Time Automatic
Foot control is standard
TIG Consumables Sold Separately

- Weight
  30 lbs
- SKU
  COR 200ACDC
Manufacturer
Coreone Welding
Equipment Fit
TIG Welding Machine
Categories
Equipment
Manual
http://manual.coreonewelding.co

There are no comments yet. Be the first to leave a comment

Please sign in to add review

Comes complete with:

• 12’ TIG Torch w/ Long Back Cap only

• 6’ Power Cable

• 8’ Gas Hose

• 13’ Ground Clamp

• Foot Pedal w/ 25’ Cord

• 3’ 110V-220V Power Adapter

• Flowmeter

• Owners Manual

• Consumables Sold Separately

COREONE 200 AC/DC Manual:

COREONE 200 AC/DC Sell Sheet:

Trouble Shooting TIG Welding

The following addresses some of the common problems of DC TIG welding. In all cases of equipment malfunction, the manufacturer’s recommendations should be strictly adhered to and followed.

Tungsten Burning Away Quickly

Possible Reason	Suggested Remedy
Incorrect Gas	Check that pure Argon is being used
No gas	Check the gas cylinder contains gas and is connected and the torch gas valve is open
Inadequate gas flow	Check the gas is connected, check hoses, gas valve and torch are not restricted. Set the gas flow between 21-30cfh flow rate
Back cap not fitted correctly	Make sure the torch back cap is fitted so that the o-ring is inside the torch body
Torch connected to DC +	Connect the torch to the DC- output terminal
Incorrect tungsten being used	Check and change the tungsten type if necessary
Tungsten being oxidised after weld is finished	Keep shielding gas flowing 10–15 seconds after arc stoppage. 1 second for each 10 amps of weld current.

Contaminated Tungsten

Possible Reason	Suggested Remedy
Touching tungsten into the weld pool	Keep tungsten from contacting weld puddle. Raise the torch so that the tungsten is off of the work piece 1/8-1/4in
Touching the filler wire to the tungsten	Keep the filler wire from touching the tungsten during welding, feed the filler wire into the leading edge of the weld pool in front of the tungsten
Tungsten melting into the weld pool	Check that correct type of tungsten is being used. Too much current for the tungsten size so reduce the amps or change to a larger tungsten

Porosity - Poor Weld Appearance and Colour

Possible Reason	Suggested Remedy
Incorrect Gas	Check that pure Argon is being used
Inadequate gas flow / gas leaks	Check the gas is connected, check hoses, gas valve and torch are not restricted. Set the gas flow between 21-30cfh flow rate. Check hoses and fittings for holes, leaks etc.,
Moisture on the base metal	Remove all moisture from base metal before welding
Contaminated base metal	Remove materials like paint, grease, oil, and dirt, including mill scale from base metal
Contaminated filler wire	Remove all grease, oil, or moisture from filler metal.
Incorrect filler wire	Check the filler wire and change if necessary

Yellowish Residue / Smoke on the Alumina Nozzle & Discolored Tungsten

Possible Reason	Suggested Remedy
Incorrect Gas	Use pure Argon gas
Inadequate gas flow	Set the gas flow between 21-30cfh flow rate
Alumina gas nozzle too small for size of tungsten being used	Increase the size of the alumina gas nozzle

Unstable Arc During DC Welding

Possible Reason	Suggested Remedy
Torch connected to DC +	Connect the torch to the DC- output terminal
Contaminated base metal	Remove materials like paint, grease, oil, and dirt, including mill scale from base metal.
Tungsten is contaminated	Remove 10mm of contaminated tungsten and re grind the tungsten
Arc length too long	Lower torch so that the tungsten is off of the work piece 2 - 5mm

Arc Wanders During DC Welding

Possible Reason	Suggested Remedy
Poor gas flow	Check and set the gas flow between 21-30cfh flow rate
Incorrect arc length	Lower torch so that the tungsten is off of the work piece 1/8-1/4in
Tungsten incorrect or in poor condition	Check that correct type of tungsten is being used. Remove 1/2in from the weld end of the tungsten and re sharpen the tungsten
Poorly prepared tungsten	Grind marks should run lengthwise with tungsten, not circular. Use proper grinding method and wheel.
Contaminated base metal	Remove contaminating materials like paint, grease, oil, and dirt, including mill scale from base metal.
Contaminated filler wire	Remove all grease, oil, or moisture from filler metal.
Incorrect filler wire	Check the filler wire and change if necessary

Arc Difficult To Start or Will Not Start DC Welding

Possible Reason	Suggested Remedy
Incorrect machine set up	Check machine set up is correct
No gas, incorrect gas flow	Check the gas is connected and cylinder valve open, check hoses, gas valve and torch are not restricted. Set the gas flow between 10 - 15 l/min flow rate
Tungsten is contaminated	Remove 10mm of contaminated tungsten and re grind the tungsten
Incorrect tungsten size and or tungsten being used	Check and change the size and or the tungsten if required
Loose connection	Check all connectors and tighten
Earth clamp not connected to work	Connect the earth clamp directly to the work piece wherever possible

Important: We strongly recommend that you check for gas leakage prior to operation of your machine. We recommend that you close the cylinder valve when the machine is not in use. Coreone as authorized representative of the manufacturer will not be liable for costs incurred due to gas leakage.

ATTENTION! - CHECK FOR GAS LEAKS

At initial set up and at regular intervals we recommend to check for gas leakage.

Recommended procedure is as follows:

Connect the regulator and gas hose assembly and tighten all connectors and clamps.
Slowly open the cylinder valve.
Set the flow rate on the regulator to approximately 21-30cfh.
Close the cylinder valve and pay attention to the needle indicator of the contents pressure gauge on the regulator, if the needle drops away towards zero there is a gas leak. Sometimes a gas leak can be slow and to identify it will require leaving the gas pressure in the regulator and line for an extended time period. In this situation it is recommended to open the cylinder valve, set the flow rate to 21-30cfh, close the cylinder valve and check after a minimum of 15 minutes.
If there is a gas loss then check all connectors and clamps for leakage by brushing or spraying with soapy water, bubbles will appear at the leakage point.
Tighten clamps or fittings to eliminate gas leakage.